If you want to know how to fix your recliner mechanism, you’re in the right place. Before we get into the accurate fixes, it’s vital to understand the fundamental components of a recliner mechanism. A reclining mechanism typically includes a cable, lever, screw, and bracket.
In this post, we will go over how to fix a recliner mechanism and provide instructions for common repairs.
Identifying the issue with your recliner mechanism is the first step toward a successful repair. Common problems include a loose or damaged cable, a faulty footrest
Contents
Troubleshooting Recliner Mechanism Problems
If you have any problems with your recliner mechanism, troubleshooting might assist you determine the source of the problem. Check for loose screws, inspect the cable for signs of wear or corrosion, and make sure all of the mechanism’s parts are in perfect alignment.
The steps for repairing the reclining mechanism on a recliner vary based on the model of recliner and the extent of the problem. However, there are some actions you can take:
Steps to repair a recliner mechanism
- Start by identifying the problem with your recliner mechanism. Common issues include a loose cable, broken lever, or malfunctioning footrest.
- Once you have identified the problem, you can proceed with the necessary repair. Let’s start with repairing the cable.
how to fix a recliner chair cable
- Using a Philips screwdriver, remove the handle from your recliner. Set the screws aside for later, and then pull the lever with your fingers, allowing it to hang loosely.
- Flip over the recliner. Find the cable under your chair and trace its path to where it connects to the metal mechanism. Remove the S-shaped end of the cable, making a mental note of where you did it.
- Using pliers or a flathead screwdriver, remove the plastic clip that holds the cable in place. If it breaks, that’s fine because the new cable includes a plastic clip. Just make careful to remove the entire clip.
- Gently pull on the handle until the broken cable is completely free of the chair.
- Thread the new cable through the hole in the handle, then pull it out from the bottom of the chair. To gain access to this area, you may need to cut a small split in the fabric of the dust cover under the chair or remove a few staples that hold the material in place. Make sure the handle sits flush in the hole.
- Insert the new clip into the slot where the old one was secured, rocking it back and forth until you hear a clicking sound and can’t pull it out.
- Insert the clip’s S-hook onto the metal chair mechanism where the original clip was secured.
- Flip the recliner over again and test the handle to ensure it works. If everything is working well, use the screws you left aside to secure the new handle in place.
how to fix a recliner chair mechanism
- If the problem with your recliner chair is not due to the cable, you may need to look at other elements of the system. Check for loose screws, tighten them as needed, and replace any broken components.
- It is also critical to ensure that the recliner chair is balanced correctly. If your chair leans to one side, adjust the footrest tension or use pliers to tighten the loose screws in the chair’s back.
- Gather the essential tools. Depending on the situation, you could require a screwdriver, pliers, or a wrench.
- Disassemble the recliner: To reach the mechanism, you will most likely need to remove the recliner’s back or the upholstery that covers it. Disassemble the recliner according to the manufacturer’s directions, or consult an expert if you are unsure.
- Examine the mechanism: Once you get access to the mechanism, inspect all of the components to determine if anything is clearly broken or damaged. Check for loose or disconnected wires, worn-out springs, and other indicators of wear and tear.
- Make repairs: Depending on your findings, you may need to replace a broken part, tighten a loose connection, or lubricate a rusted component. Follow the manufacturer’s instructions or seek professional advice on completing the necessary repairs.
- Reassemble the recliner: After you’ve repaired the mechanism, reassemble it in the reverse sequence of disassembly. Before attempting to use the reclining feature, ensure that all of the parts are properly attached.
- Once you’ve reassembled the chair, verify the reclining mechanism to ensure it’s working properly. If everything appears to be in working order, you’re all set! If not, you may need to investigate deeper or get professional assistance.
continue how to fix a recliner chair footrest
recommended the BEST 11 RECLINER CHAIRS
